Product Search
Search results for 'C-293'
Showing 21 - 41 of 563 Total Results
Fresh Concrete Field Testing Kits, 6" x 12"
CA-0510
Location: Fresh Concrete Field Testing
Fresh concrete kits contain everythiung you need for routine testing of fresh concrete testing in the field, with all items meeting ASTM standards.
(3) options
Location: Beam Testers
Self-contained shock-proof portable concrete beam tester accurately and easily determines flexural strengths of 6 x 6 in. cross-section beams - from Test Mark.
(4) options
Location: Test Platens
Test both cubes and cylinders . Used for testing 2” (50 mm) cubes and 3” (76 mm) diameter cylinders and cores in compression. Cube test set consists of a spherically seated platen assembly and a lower pedestal used for positioning the cube sample at the correct height for testing. The bearing block...
(3) options
Location: Test Platens
Used to determine the splitting tensile strength of concrete cylinders. . The cylinder splitting head has a bearing contact area of 12” (304 mm) long by 2” (50 mm) wide, its surface is machined plane to .001” (.025 mm) and has a scribed center line of the face of the bar for easier centering of...
MA-0802
Location: Draw Rod Assembly
Safer, easier and faster changing of test platens and spacers. . The draw rod system is used to adjust the inside vertical working height of the load frame, to allow for testing samples of different heights through the use of spacers and test platens. The system is made up of a steel hand wheel...
CA-0600-P
Location: Air Entrainment/Roll-A-Meter
The PVC and fiberglass reinforced Roll-A-Meter from Test Mark measures entrained air in any type of concrete, including lightweight mixes.
CA-0286
Location: Cube Molds
The 2-inch cube maker molding system from Test Mark uses watertight polypropylene liners which fit into a 3-gang metal mold frame.
AA-0011
Location: Marshall Basic Compression Testing
The lower segment of the Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments - from Test Mark.
SA-2000
Location: CBR Load Frames
The CBR (California Bearing Ratio) loading press from Test Mark uses a two-position mechanical jack to provide steady test speeds, as well as rapid travel of the platen for positioning of the sample.
Marshall Compaction Stationary Mold, 4"
AA-0045
Location: Marshall 4" Compaction Molds
Marshall Compaction Stationary Mold is for hand and non-rotating base compactors and is machined from seamless tubing and plated - from Test Mark Industries.
SA-4010
Location: Dynamic Cone Penetrometer
The Dual Mass DCP Standard Kit from Test Mark measures the shear strength of soil with a CBR between 0.5 - 100%.
(8) options
Location: Cylinder Molds - Plastic
Test Mark Industries features plastic concrete cylinder molds as part of a complete line of concrete testing equipment.
AA-0010
Location: Marshall Basic Compression Testing
The lower segment of Test Mark's Marshall breaking head is mounted on a base with two vertical guide rods to connect the upper and lower segments.
Constant/Falling Head Permeameter Set
(5) options
Location: Constant/Falling Head Permeameter Set
Constant/Falling Head Permeameter Set for use with granular soils in determining the coefficient of permeability via the constant or falling-head method for laminar flow of water.
(4) options
Location: Cylinder Molds - Steel
Test Mark Industries features steel concrete cylinder molds as part of a complete line of concrete testing equipment.
Cylinder Platen, 6 ½” Diameter
(3) options
Location: Test Platens
Free floating bearing platen seats under test pressure. . Used when testing 6” (152 mm) or 4” (101 mm) diameter concrete cylinders in compression. Platen is manufactured from steel with all components plated for corrosion resistance. Upper cylinder platen used when testing 6” (152 mm) or 4” (101...
(2) options
Location: Proctor Molds, split
Split proctor molds from Test Mark are manufactured from steel with all parts plated for longer life.
SA-0362
Location: Plastic Limit
Test Mark's Plastic Limit Roller for soils is a unique time-saving device designed to produce consistent results by an easily repeatable mechanical technique.
CA-0355-SP
Location: Self-Consolidating Concrete
Test Mark's J-Ring Test Set is used to characterize the ability of self-consolidating concrete (SCC) to pass through reinforcing steel.
Spacers for CM-0030 and CM-2500 series
(4) options
Location: Spacers
Spacers are used with test platens to adjust the vertical working clearance height inside a machines load frame, for testing samples of various types and sizes to prevent over-extension of the load frames piston. They are manufactured from steel and machined plane on both ends to maintain a...
